Singapore ISO Consultants

ISO 9001

2010-08-12T07:12:00.000-07:00

ISO 9001:2008 is part of the ISO 9000 family of standards, and is the document that lists the requirements an organization must comply with to become ISO 9001 Registered. ISO 9001 is an internationally recognized Quality Management System.

"ISO 9000 Certified" is technically incorrect as ISO 9000 does not have requirements.
"ISO 9001 Certified" means an organization has met the requirements in ISO9001. It defines an ISO 9000 Quality Management System (QMS).
ISO 9001:2000 was replaced by ISO 9001:2008 in the year 2008. (ISO 9001:2000 is now obsolete) ISO 9001:2008 is focused on meeting customer expectations and delivering customer satisfaction so you must pay attention to the customer.
ISO9001 evaluates whether your quality management system is appropriate and effective, while forcing you to identify and implement improvements.
Continuous improvement assures your customers benefit by receiving products/services that meet their requirement, and that you deliver consistent performance.
Internally, the organization will profit from increased job satisfaction, improved morale, and improved operational results (reduced scrap and increased efficiency).
Meeting legal and regulatory requirements benefit the community.

ISO 9001 does NOT define the actual quality of your product or service. The standard helps you achieve consistent results and continually improve the process. Thus, if you can make a good product most of the time, this helps you make it all of the time. It's just good business practices

ISO 9000 Standards

2010-08-12T07:05:00.000-07:00

ISO 9000 Standards

ISO 9000 is a family of standards for quality management systems. ISO 9000 is maintained by ISO, the International Organization for Standardization and is administered by accreditation and certification bodies. The rules are updated, as the requirements motivate changes over time. Some of the requirements in ISO 9001:2008 (which is one of the standards in the ISO 9000 family) include

a set of procedures that cover all key processes in the business;
monitoring processes to ensure they are effective;
keeping adequate records;
checking output for defects, with appropriate and corrective action where necessary;
regularly reviewing individual processes and the quality system itself for effectiveness; and
facilitating continual improvement

A company or organization that has been independently audited and certified to be in conformance with ISO 9001 may publicly state that it is "ISO 9001 certified" or "ISO 9001 registered". Certification to an ISO 9001 standard does not guarantee any quality of end products and services; rather, it certifies that formalized business processes are being applied.
Although the standards originated in manufacturing, they are now employed across several types of organizations. A "product", in ISO vocabulary, can mean a physical object, services, or software.

The ISO 9000 Family has several standards, and they are the exact same standard across the globe even though they are called by different names. Each member country has their own entity authorized by ISO to manage the standards, but they are all the same exact ISO 9000 documents and set of requirements.

Australia - AS/NZS ISO 9001:2008 (Standards Australia)
Unites States - ANSI ISO 9001:2008 (American National Standards Institute)
United Kingdom - BSI ISO 9001:2008 (British Standards Institution)
Etc. (See Complete list of ISO Member Countries)

Here is the ISO 9000 Family of Standards. Click each link for more information.

ISO 9000 (2005) Fundamentals & Vocabulary for ISO 9000 Standards
- Learn about the ISO 9000 Standard
- Buy ISO 9000:2005
ISO 9001 (2008) The Requirements of the ISO 9000 Standard
- Learn about the ISO 9001 Standard (Free Tutorial)
- Learn changes from ISO 9001:2000 to ISO 9001:2008
- Buy ISO 9001:2008
ISO 9002 (Obsolete) Companies that manufacture but don't design
- Learn about the ISO 9002 Standard
ISO 9003 (Obsolete) Companies that perform Inspection and Test
- Learn about the ISO 9003 Standard
ISO 9004 (2009) Managing for the sustained success of an organization
- Learn about the ISO 9004 Standard
- Buy ISO 9004:2009
ISO 9000 Supporting Standards (Auditing, Industry Specific Guidance, etc.)
Who is ISO?
What is a Process Approach?
What is a Quality Management System?
Where can I buy a copy of the ISO 9000 Standards?

What is the ISO 9000 Series?

It is important to have standard operating procedures in the global market. The ISO 9000 series of documents was created by the International Organization for Standardization (ISO) as international requirements for quality management systems. Now that ISO 9000 is present in more than 80 countries with over one million registrations it is common in the business world.
The ISO 9000 standards are a set of international quality management system standards and guidelines. The term ISO9000 refers to a group of quality management standards which are process standards (not product standards). They were originally introduced as ISO 9000:2000.
ISO 9000 currently includes three quality standards:

ISO 9000:2005 Fundamentals and Vocabulary used in the ISO 9000 Standards
ISO 9001:2008 (which replaced ISO 9001:2000) contains the actual requirements an
organization must comply with to become ISO 9001 Registered.
- Requirements of ISO 9001 outlines the clauses of ISO 9001:2008.
ISO 9004:2009 Managing for the sustained success of an organization.

ISO 9001:2008 lists requirements, while ISO 9000:2000 and ISO 9004:2009 are Quality Guidelines. People often say "ISO 9000 certified", but what they mean is they have met the requirements of the ISO 9001 standard. Read more...

The series is not industry specific and is applicable to any manufacturing or service organization. It is managed by Technical Committee (TC) 176, comprised of international members from many industries and backgrounds.

What are the older (obsolete) ISO 9000 Standards?

ISO 9000 (1994) originally had three QMS models depending on the primary function:

ISO 9001:1994 Model for quality assurance in design, development, production,
installation, and servicing was for companies and organizations whose activities included the creation of new products.
- Learn about ISO 9001
ISO 9002:1994 Model for quality assurance in production, installation, and servicing had basically the same material as ISO 9001 but without covering the creation of new products.
- Learn about ISO 9002
ISO 9003:1994 Model for quality assurance in final inspection and test covered only the final inspection of finished product, with no concern for how the product was produced.
- Learn about ISO 9003

All of these items were combined into ISO 9001:2000, which is now ISO 9001:2008.

What Standards support the ISO 9000 family?

Other standards were created to support the ISO 9000 family, and not all start with ISO 9xxx. Click on the link to buy a copy from Tech Street - the authorized reseller of ISO Standards:

ISO 10001 (2007) Quality Management - Customer Satisfaction -- Guidelines for Codes of
Conduct for Organizations
ISO 10002 (2004) Quality Management - Customer Satisfaction - Guidelines for Complaints
Handling in Organizations
ISO 10003 (2007) Quality Management - Customer Satisfaction - Guidelines for Dispute
Resolution External to Organizations
ISO 10004 (2010) Processes to monitor/measure customer satisfaction.
ISO 10005 (2005) Guidelines for the development, review, acceptance, application and
revision of quality plans.
ISO 10006 (2003) Guidance on the application of quality management in projects.
ISO 10007 (2003) Quality management systems - Guidelines for configuration management
ISO 10013 (2001) Guidelines for Quality Management System Documentation
ISO 10014 (2006) Guidelines for Realizing Financial and Economic benefits
ISO 10015 (1999) Quality Management - Guidelines for Training
ISO 10019 (2005) Selection of Quality Management Consultants and Use of their Services
ISO 10017 (2003) Guidance on Statistical Techniques for ISO 9001
ISO 15161 (2001) Guidelines on the Application of ISO 9001 for the Food & Drink Industry
ISO 16106 (2006) Packaging - Applying 9001 to Transport Packages for Dangerous Goods
ISO 15489-1 (2001) Information & Documentation-Records Management -Part 1: General
ISO 15489-2 (2001) Information & Documentation-Records Management -Part 2: Guidelines
ISO 19011 (2002) Guidelines for quality and/or environmental mgmt systems auditing
- Learn about ISO 19011
ISO 90003 (2004) Software Engineering - Application of ISO 9001 to Computer Software
Etc.

resources: the9000store.com
Contents from wikipedia

What is ISO?

2010-08-11T21:46:00.000-07:00

International Organization for Standardization

From Wikipedia, the free encyclopedia




Formation	23 February 1947
Type	NGO
Purpose/focus	International standardization
Headquarters	Geneva, Switzerland
Membership	165 members
Official languages	English, French and Russian
Website	http://www.iso.org/

The International Organization for Standardization (French: Organisation internationale de normalisation, Russian: Международная организация по стандартизации, tr. Mezhdunarodnaya organizaciya po standartizacii ^{[citation needed]}), widely known as ISO, is an international-standard-setting body composed of representatives from various national standards organizations. Founded on 23 February 1947, the organization promulgates worldwide proprietary industrial and commercial standards. It has its headquarters in Geneva, Switzerland.^[1] While ISO defines itself as a non-governmental organization, its ability to set standards that often become law, either through treaties or national standards, makes it more powerful than most non-governmental organizations.^{[citation needed]} In practice, ISO acts as a consortium with strong links to governments.^{[citation needed]}

Name and abbreviation
The organization's logos in two of its official languages, English and French, include the word ISO (pronounced /ˈaɪsoʊ/), and it is usually referred to by this short-form name. ISO is not an acronym or initialism for the organization's full name in either official language. Rather, the organization adopted ISO based on the Greek word isos (ἴσος), meaning equal. Recognizing that the organization’s initials would be different in different languages, the organization's founders chose ISO as the universal short form of its name. This, in itself, reflects the aim of the organization: to equalize and standardize across cultures.^[2]^[3]

History

Standards are important in international trade because incongruent standards can be barriers to trade, giving some organizations advantages in certain areas of the world. Standards provide clear identifiable references that are recognized internationally and encourage fair competition in free-market economies. Standards facilitate trade through enhanced product quality and reliability, greater interoperability and compatibility, greater ease of maintenance and reduced costs. ISO covers a wide variety of standards with the exception of electrical and electronic engineering standards covered by the International Electrotechnical Commission (IEC), telecommunication standards covered by the International Telegraph Union (ITU) and information technology covered by JTC 1 (a joint committee between ISO and IEC). ^[4]
The organization which today is known as ISO began in 1926 as the International Federation of the National Standardizing Associations (ISA). This organization focused heavily on mechanical engineering. It was disbanded in 1942 during the second World War but was re-organized under the current name, ISO, in 1946.
Even the name of the organization is standardized. The name, "ISO" is not an acronym but was derived from the Greek word "isos" meaning "equal". (The relation to standards is that if two objects meet the same standard, they should be equal.) This name eliminates any confusion that could result from the translation of "International Organization For Standardization" into different languages which would lead to different acronyms.
ISO is a voluntary organization whose members are recognized standard authorities, each one representing one country. The bulk of the work of ISO is done by the 2700 technical committees, subcommittees and working groups. Each committee and subcommittee is headed by a Secretariat from one of the member organizations. The American National Standards Institute (ANSI) is the United States representative to ISO. The ANSI ASC Z-1/ASQ Standards Group coordinates the United States representation in the ISO Technical Committees 176 and 207 which are concerned with the ISO 9000 and ISO 14000 standards respectively.

International Standards and other publications

Standardization process

A standard published by ISO/IEC is the last stage of a long process that commonly starts with the proposal of new work within a committee. Here are some abbreviations used for marking a standard with its status:

PWI - Preliminary Work Item
NP or NWIP - New Proposal / New Work Item Proposal (e.g. ISO/IEC NP 23007)
AWI - Approved new Work Item (e.g. ISO/IEC AWI 15444-14)
WD - Working Draft (e.g. ISO/IEC WD 27032)
CD - Committee Draft (e.g. ISO/IEC CD 23000-5)
FCD - Final Committee Draft (e.g. ISO/IEC FCD 23000-12)
DIS - Draft International Standard (e.g. ISO/IEC DIS 14297)
FDIS - Final Draft International Standard (e.g. ISO/IEC FDIS 27003)
PRF - Proof of a new International Standard (e.g. ISO/IEC PRF 18018)
IS - International Standard (e.g. ISO/IEC 13818-1:2007)

Abbreviations used for amendments :

NP Amd - New Proposal Amendment (e.g. ISO/IEC 15444-2:2004/NP Amd 3)
AWI Amd - Approved new Work Item Amendment (e.g. ISO/IEC 14492:2001/AWI Amd 4)
WD Amd - Working Draft Amendment (e.g. ISO 11092:1993/WD Amd 1)
CD Amd / PDAmd - Committee Draft Amendment / Proposed Draft Amendment (e.g. ISO/IEC 13818-1:2007/CD Amd 6)
FPDAmd / DAM (DAmd) - Final Proposed Draft Amendment / Draft Amendment (e.g. ISO/IEC 14496-14:2003/FPDAmd 1)
FDAM (FDAmd) - Final Draft Amendment (e.g. ISO/IEC 13818-1:2007/FDAmd 4)
PRF Amd - (e.g. ISO 12639:2004/PRF Amd 1)
Amd - Amendment (e.g. ISO/IEC 13818-1:2007/Amd 1:2007

Other abbreviations :

TR - Technical Report (e.g. ISO/IEC TR 19791:2006)
DTR - Draft Technical Report (e.g. ISO/IEC DTR 19791)
TS - Technical Specification (e.g. ISO/TS 16949:2009)
DTS - Draft Technical Specification (e.g. ISO/DTS 11602-1)
PAS - Publicly Available Specification
TTA - Technology Trends Assessment (e.g. ISO/TTA 1:1994)
IWA - International Workshop Agreement (e.g. IWA 1:2005)
Cor - Technical Corrigendum (e.g. ISO/IEC 13818-1:2007/Cor 1:2008)
Guide - a guidance to technical committees for the preparation of standards

International Standards are developed by ISO technical committees (TC) and subcommittees (SC) by a process with six steps:^[9]^[16]

Stage 1: Proposal stage
Stage 2: Preparatory stage
Stage 3: Committee stage
Stage 4: Enquiry stage
Stage 5: Approval stage
Stage 6: Publication stage

The TC/SC may set up working groups (WG) of experts for the preparation of a Working Drafts. Subcommittees may have several working groups, which can have several Sub Groups (SG).

Stages in the development process of an ISO standard^[8]^[9]^[10]^[13]^[16]^[14]
Stage code	Stage	Associated document name	Abbreviations	Description
00	Preliminary stage	Preliminary work item	PWI
10	Proposal stage	New work item proposal	NP or NWIP, NP Amd/TR/TS/IWA
20	Preparatory stage	Working draft(s)	AWI, AWI Amd/TR/TS, WD, WD Amd/TR/TS
30	Committee stage	Committee draft(s)	CD, CD Amd/Cor/TR/TS, PDAmd (PDAM), PDTR, PDTS
40	Enquiry stage	Enquiry draft	DIS, FCD, FPDAmd, DAmd (DAM), FPDISP, DTR, DTS	(CDV in IEC)
50	Approval stage	final draft International Standard	FDIS, FDAmd (FDAM), PRF, PRF Amd/TTA/TR/TS/Suppl, FDTR
60	Publication stage	International Standard	ISO TR, TS, IWA, Amd, Cor
90	Review stage		ISO TR, TS, IWA, Amd, Cor
95	Withdrawal stage

It is possible to omit certain stages, if there is a document with a certain degree of maturity at the start of a standardization project - for example a standard developed by another organization. ISO/IEC Directives allow also the so-called "Fast-track procedure". In this procedure a document is submitted directly for approval as a draft International Standard (DIS) to the ISO member bodies or as a final draft International Standard (FDIS) if the document was developed by an international standardizing body recognized by the ISO Council.^[9]
The first step - a proposal of work (New Proposal) is approved at the relevant subcommittee or technical committee (e.g. SC29 and JTC1 respectively in the case of Moving Picture Experts Group - ISO/IEC JTC1/SC29/WG11). A working group (WG) of experts is set up by the TC/SC for the preparation of a Working Draft. When the scope of a new work is sufficiently clarified, some of the working groups (e.g. MPEG) usually make open request for proposals - known as "Call for proposals". The first document that is produced for example for audio and video coding standards is called a Verification Model (VM) (previously also called a Simulation and Test Model). When a sufficient confidence in the stability of the standard under development is reached, a Working Draft (WD) is produced. This is in the form of a standard but is kept internal to working group for revision. When a Working Draft is sufficiently solid and the working group is satisfied that it has developed the best technical solution to the problem being addressed, it becomes Committee Draft (CD). If it is required, it is then sent to the P-members of the TC/SC (National Bodies) for ballot.
The CD becomes Final Committee Draft (FCD) if the number of positive votes is above the quorum. Successive committee drafts may be considered until consensus is reached on the technical content. When it is reached, the text is finalized for submission as a draft International Standard (DIS). The text is then submitted to National Bodies for voting and comment within a period of five months. It is approved for submission as a final draft International Standard (FDIS) if a two-thirds majority of the P-members of the TC/SC are in favour and not more than one-quarter of the total number of votes cast are negative. ISO will then hold a ballot with National Bodies where no technical changes are allowed (yes/no ballot), within a period of two months. It is approved as an International Standard (IS) if a two-thirds majority of the P-members of the TC/SC is in favour and not more than one-quarter of the total number of votes cast are negative. After approval, only minor editorial changes are introduced into the final text. The final text is sent to the ISO Central Secretariat which publishes it as the International Standard.^[7]^[9]

ISO document copyright

ISO documents are copyrighted and ISO charges for copies of most. ISO does not, however, charge for most draft copies of documents in electronic format. Although useful, care must be taken using these drafts as there is the possibility of substantial change before it becomes finalized as a standard. Some standards by ISO and its official U.S. representative (and the International Electrotechnical Commission's via the U.S. National Committee) are made freely available.^[18]^[19]

Members

A map of standards bodies who are ISO members
Key:
members correspondent members subscriber members other places with an ISO 3166-1 code who aren't members of ISO

ISO has 163 national members,^[20] out of the 203 total countries in the world.
ISO has three membership categories:

Member bodies are national bodies that are considered to be the most representative standards body in each country. These are the only members of ISO that have voting rights.
Correspondent members are countries that do not have their own standards organization. These members are informed about ISO's work, but do not participate in standards promulgation.
Subscriber members are countries with small economies. They pay reduced membership fees, but can follow the development of standards.

Participating members are called "P" members as opposed to observing members which are called "O" members.

Products named after ISO

The fact that many of the ISO-created standards are ubiquitous has led, on occasion, to common use of "ISO" to describe the actual product that conforms to a standard. Some examples of this are:

CD images end in the file extension "ISO" to signify that they are using the ISO 9660 standard filesystem as opposed to another file system - hence CD images are commonly referred to as "ISOs". Virtually all computers with CD-ROM drives can read CDs that use this standard. Some DVD-ROMs also use ISO 9660 filesystems.
Photographic film's sensitivity to light, its "film speed," is described by ISO 5800:1987. Hence, the film's speed is often referred to as its "ISO number."

ISO/IEC Joint Technical Committee 1

Main article: ISO/IEC JTC1

To deal with the consequences of substantial overlap in areas of standardization and work related to information technology, ISO and IEC formed a Joint Technical Committee known as the ISO/IEC JTC1. It was the first such joint committee. The second joint committee was created in 2009 - Joint Project Committee - Energy efficiency and renewable energy sources - Common terminology (ISO/IEC/JTC 2).^[21]

IWA document

Like ISO/TS, International Workshop Agreement (IWA) is another armoury of ISO for providing rapid response to requirements for standardization in areas where the technical structures and expertise are not currently in place ^{[citation needed]}. The utility harmonizes technical urgency industrial wide.

Criticism

With the exception of a small number of isolated standards,^[22] ISO standards are normally not available free of charge, but for a purchase fee,^[23] which has been seen by some as too expensive for small Open source projects.^[24]
The ISO/IEC JTC1 fast-track procedures ("Fast-track" as used by OOXML and "PAS" as used by OpenDocument) have garnered criticism in relation to the standardization of Office Open XML (ISO/IEC 29500). Martin Bryan, outgoing Convenor of ISO/IEC JTC1/SC34 WG1, is quoted as saying:

I would recommend my successor that it is perhaps time to pass WG1’s outstanding standards over to OASIS, where they can get approval in less than a year and then do a PAS submission to ISO, which will get a lot more attention and be approved much faster than standards currently can be within WG1.

The disparity of rules for PAS, Fast-Track and ISO committee generated standards is fast making ISO a laughing stock in IT circles. The days of open standards development are fast disappearing. Instead we are getting 'standardization by corporation'.^[25]

Computer security entrepreneur and Ubuntu investor, Mark Shuttleworth, commented on the Standardization of Office Open XML process by saying

I think it de-values the confidence people have in the standards setting process,

and Shuttleworth alleged that ISO did not carry out its responsibility. He also noted that Microsoft had intensely lobbied many countries that traditionally had not participated in ISO and stacked technical committees with Microsoft employees, solution providers and resellers sympathetic to Office Open XML.

When you have a process built on trust and when that trust is abused, ISO should halt the process ... ISO is an engineering old boys club and these things are boring so you have to have a lot of passion … then suddenly you have an investment of a lot of money and lobbying and you get artificial results. The process is not set up to deal with intensive corporate lobbying and so you end up with something being a standard that is not clear.^[26]

References

^ "Discover ISO – Meet ISO"

. ISO. © 2007. http://www.iso.org/iso/about/discover-iso_meet-iso.htm
. Retrieved 7 September 2007.
^ "ISO's name"

. ISO. 2007. http://www.iso.org/iso/en/networking/pr/isoname/isoname.html
. Retrieved 7 September 2007.
^ "Discover ISO – ISO's name"

. ISO. 2007. http://www.iso.org/iso/about/discover-iso_meet-iso/discover-iso_isos-name.htm
. Retrieved 7 September 2007.
^ [1]

A Brief History of ISO
^ ^a ^b ^c ^d ^e The ISO directives are published in two distinct parts:
* "ISO Directives, Part 2: Rules for the structure and drafting of International Standards. 5th Edition"

(pdf). ISO/IEC. 2004. https://docs.google.com/viewer?url=http://www.iec.ch/tiss/iec/Directives-Part2-Ed5.pdf&embedded=true
. Retrieved 7 September 2007.
^ ISO. "ISO/IEC Directives and ISO supplement"

. http://www.iso.org/directives
. Retrieved 1 January 2010.
^ ^a ^b ^c "About MPEG"

. chiariglione.org. http://mpeg.chiariglione.org/about_mpeg.htm
. Retrieved 13 December 2009.
^ ^a ^b ^c ISO. "International harmonized stage codes"

. http://www.iso.org/iso/standards_development/processes_and_procedures/stages_description/stages_table.htm#s90
. Retrieved 31 December 2009.
^ ^a ^b ^c ^d ^e ^f ISO. "Stages of the development of International Standards"

. http://www.iso.org/iso/standards_development/processes_and_procedures/stages_description.htm
. Retrieved 31 December 2009.
^ ^a ^b ^c "The ISO27k FAQ - ISO/IEC acronyms and committees"

. IsecT Ltd.. http://www.iso27001security.com/html/faq.html#Acronyms
. Retrieved 31 December 2009.
^ ^a ^b ^c ISO (2007). "ISO/IEC Directives Supplement — Procedures specific to ISO"

(PDF). https://docs.google.com/viewer?url=http://www.astm.org/COMMIT/1st_Supplement.pdf&embedded=true
. Retrieved 31 December 2009.
^ ^a ^b ^c ISO (2007). "List of abbreviations used throughout ISO Online"

. http://www.iso.org/iso/support/faqs/faqs_list_abbreviations.htm
. Retrieved 31 December 2009.
^ ^a ^b ^c "US TAG COMMITTEE HANDBOOK"

(DOC). 2008-03. https://docs.google.com/viewer?url=http://www.sae.org/exdomains/standardsdev/global_resources/US%2520TAG%2520Committe%2520Handbook%25206March2008.doc&embedded=true
. Retrieved 1 January 2010.
^ ^a ^b ^c ISO/IEC JTC1 (2 November 2009), Letter Ballot on the JTC 1 Standing Document on Technical Specifications and Technical Reports

, https://docs.google.com/viewer?url=http://isotc.iso.org/livelink/livelink/JTC001-N-9876.pdf?func=doc.Fetch&nodeId=8498789&docTitle=JTC001-N-9876&embedded=true
, retrieved 1 January 2010
^ ISO. "ISO deliverables"

. http://www.iso.org/iso/standards_development/processes_and_procedures/deliverables.htm
. Retrieved 9 April 2010.
^ ^a ^b ISO (2008) (PDF), ISO/IEC Directives, Part 1 - Procedures for the technical work, Sixth edition, 2008

, https://docs.google.com/viewer?url=http://www.iec.ch/tiss/iec/Directives-Part1-Ed6.pdf&embedded=true
, retrieved 1 January 2010
^ ISO, IEC (5 November 2009). "ISO/IEC JTC 1/SC 29, SC 29/WG 11 Structure (ISO/IEC JTC 1/SC 29/WG 11 - Coding of Moving Pictures and Audio)"

. http://www.itscj.ipsj.or.jp/sc29/29w12911.htm
. Retrieved 7 November 2009.
^ "Freely Available ISO Standards"

. ISO. Last updated 2007-08-08. http://isotc.iso.org/livelink/livelink/fetch/2000/2489/Ittf_Home/PubliclyAvailableStandards.htm
. Retrieved 7 September 2007.
^ "Free ANSI Standards"

. http://webstore.ansi.org/ansidocstore/free_standards.asp
. Retrieved 19 June 2007.
^ "General information on ISO"

. ISO. © 2009. http://www.iso.org/iso/support/faqs/faqs_general_information_on_iso.htm
. Retrieved 29 January 2009.
^ "ISO/IEC/JTC 2 - Joint Project Committee - Energy efficiency and renewable energy sources - Common terminology"

. http://www.iso.org/iso/standards_development/technical_committees/list_of_iso_technical_committees/iso_technical_committee.htm?commid=585141
. Retrieved 1 January 2010.
^ "Freely Available Standards"

. ISO. http://standards.iso.org/ittf/PubliclyAvailableStandards/index.html
. Retrieved 26 April 2008.
^ "Shopping FAQs"

. ISO. http://www.iso.org/iso/store/shopping_faqs.htm
. Retrieved 26 April 2008.
^ Jelliffe, Rick (1 August 2007). "Where to get ISO Standards on the Internet free"

. oreillynet.com. http://www.oreillynet.com/xml/blog/2007/08/where_to_get_iso_standards_on.html
. Retrieved 26 April 2008. "The lack of free online availability has effectively made ISO standard irrelevant to the (home/hacker section of the) Open Source community"
^ "Report on WG1 activity for December 2007 Meeting of ISO/IEC JTC1/SC34/WG1 in Kyoto"

. iso/jtc1 sc34. 29 November 2007. http://www.jtc1sc34.org/repository/0940.htm
.
^ "Ubuntu’s Shuttleworth blames ISO for OOXML’s win"

. ZDNet.com. 1 April 2008. http://blogs.zdnet.com/open-source/?p=2222
.

External links

Official website

(free access to the catalogue of standards only, not to the contents)
Publicly Available Standards

(free access to a small subset of the standards)
ISO/TC 37 "Terminology and other language and content resources", a fundamental committee for all ISO standardization projects
ISO/IEC JTC1
ISO Advanced search for standards and/or projects
ISO Concept Database

(terminology database of ISO standards)

Work Place Safety and Health Risk Consultants

2010-07-20T17:55:00.001-07:00

Work Place Safety and Health Risk Consultants

In-house training

We provide in-house training for RISK Management, to meet MOM regulations related to WORK PLACE SAFETY and HEALTH ACT.

Work Place Safety and Health Risk Assessment

We conduct RISK Assessments to meet MOM regulations.

SMC (Safety Management Certification for Small Construction companies)SMS Audits(Safety Management System Audits)

We can help you to implement SMC to meet BCA requirements and get certified.

We can help you in:

SLOTS registration / renewal,

Singapore BCA Contractor grades C1 C2 B1 B2 A1 A2. Upgrade to BCA grades C1 C2 B1 B2 A2 A1

Singapore Structural Steel society registration

Other ISO Standards

2010-07-20T17:53:00.000-07:00

Others Standards

AS 9000
ISO 90 01
ISO/TS
16949
QS 9000
ISO 13485SS 524
ISO 17025
ISO 14001
ISO 22000
HACCP
SS444
SA 8000
ISO 27001
ISMS-ISO 17799
BS 7799
OHSAS 18001
SMC
SCC
SS 506
CP 79

OHSAS 18001 Upgrading

2010-07-20T17:50:00.000-07:00

OHSAS 18001

OHSAS 18001 Upgrading

ISO 18001:2007 Upgrading - online service

Now you can upgrade your OHSAS 18001 Documentation
to meet requirements of NEW version of the standard
with out leaving your desk.
How It Works?Make payment (Select the Standard and click "Add to Cart" button on the right corner of this
page). Email us your payment receipt number and soft copy of your OHSAS 18001 Documents
in EDITABLE text format (e.g Microsoft WORD or EXCEL files). We will amend and email back
your documents to meet the requirements of new version of the standard OHSAS 18001:2007.

Can we make Cheque payments or through other means?Yes, you can pay through Bank cheques or other means. Email us to work out a payment
method suitable for you.

How long it takes to upgrade?If you send us your OHSAS 18001 Documents in EDITABLE text format (e.g Microsoft WORD or
EXCEL files, it takes 10 (Ten) working days to revise and send back your documents. Count 7
days from the date you have sent the complete set of documents and payment.

How much it cost to upgrade on line?S$800 (Singapore Dollars Eight Hundreds Only), if you send us your OHSAS 18001 Documents
in EDITABLE text format (e.g Microsoft WORD or EXCEL files).

From which country we can use this online upgrading service?You can use this online service from any country or region or part of the world.

Is it possible to interact or communicate or talk with the consultant who is handling our
project?Yes, you can interact or communicate or talk with the consultant through phone, fax, email or
chat on msn or yahoo or skype.

We do not have editable text files for our OHSAS 18001 documents, we only have printed
copy, can we still use this online upgrading service?Yes, you can use our online upgrading service if you only have printed copies. You can send us
scanned copies as pdf or tiff files or courier your printed copies to us. But there will be
additional charges to convert your pdf or tiff files or printed copies to Microsoft WORD or EXCEL
files). Contact us through email or phone or fax for a quotation.

What are the documents we need to send?You need to send the following documents for us to completely upgrade:
Safety Policy Statements
Safety Objectives
Safety Manual
Safety Procedures
Emergency Response Plans
Management Programme
Copy of Local Health and Safety Regulations
Material safety Data Sheets
Risk Assessment records, Risk Control plans
Standard Forms

Our OHSAS 18001 is integrated with ISO 9001, can we still use this online upgrading
service?Yes, Integrated OHSAS 18001 & ISO 9001 documents can be upgraded. Pay for both Standards
and send the payment receipt numbers and the integrated OHSAS 18001 & ISO 9001
documents.

Our OHSAS 18001 is integrated with ISO 14001 or other standards, can we still use this
online upgrading service?Yes, We can upgrade the OHSAS 18001 part on your integrated Management system
Documents. Pay only for OHSAS 18001 upgrading and send the payment receipt number and
the Integrated Management system Documents.

Read more...

ISO 14001 Consultants

2010-07-20T17:47:00.000-07:00

ISO 14001
It helps organizations to minimize the harmful effects caused by their activities on the environment, and enable them to continually improve on their environmental performance.

The ISO 14000 standards are practical tools for implementing
a strategic approach that can bring return on investment in environment-related measures.

The systematic ISO 14001 approach requires the organization to take a hard look at all areas where its activities have an environmental impact. And it can lead to benefits like the following:

* reduced cost of waste management
* savings in consumption of energy and materials
* lower distribution costs
* improved corporate image among regulators, customers and the public
* framework for continual improvement of environmental performance.

It also helps to avoid pollution that could cost the company a fine for infringing environmental legislation.
Read more...

ISO 9001-Quality Management

2010-07-20T17:45:00.000-07:00

It is used in a wide range of organizations, including colleges and universities, as well as services, such as personal financial planning.It is recognized as an international reference for quality requirements in business to business dealings. ISO 9001 is adopted in over 160 countries and economies, making it the most recognized ISO standard. Read more.....

List of ISO Standards

2010-06-28T12:42:00.000-07:00

ISO 1–ISO 999

ISO 1 Standard reference temperature for geometrical product specification and verification
ISO 2 Textiles — Designation of the direction of twist in yarns and related products
ISO 3 Preferred numbers ^{[clarification needed]}
ISO 4 Rules for the abbreviation of title words and titles of publications
ISO 7 Pipe threads where pressure-tight joints are made on the threads ^{[clarification needed]}
ISO 9 Information and documentation — Transliteration of Cyrillic characters into Roman characters — Slavic and non-Slavic languages
ISO 16:1975
Acoustics — Standard tuning frequency (Standard musical pitch)
ISO 31 Quantities and units
ISO 65 Carbon steel tubes suitable for screwing in accordance with ISO 7-1^[2]
ISO 68-1 ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads^[3]
ISO 68-2 ISO general purpose screw threads — Basic profile — Part 2: Inch screw threads
ISO 128 Technical drawings — General principles of presentation
ISO 216 paper sizes, e.g. the A4 paper size
ISO 226 Phon based on Fletcher-Munson curves
- ISO 226:2003 Phon based on newer Equal-loudness contours
ISO 228-1: Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation.
ISO 233:1984 Transliteration of Arabic characters into Roman characters
- ISO 233-2:1993 Transliteration of Arabic characters into Roman characters — Part 2: Arabic language — Simplified transliteration
ISO 259:1984 Documentation — Transliteration of Hebrew characters into Roman characters
- ISO 259-2:1994 Transliteration of Hebrew characters into Roman characters — Part 2: Simplified transliteration
ISO 261 General purpose metric screw threads. General plan.
ISO 262 Selected metric-screw-thread sizes for screws, bolts, and nuts
ISO 361 Basic ionizing radiation symbol
ISO 500 Agricultural tractors — Rear-mounted power take-off
ISO 639 Codes for the representation of names of languages
- ISO 639-1 Codes for the representation of names of languages — Part 1: Alpha-2 code
- ISO 639-2 Codes for the representation of names of languages — Part 2: Alpha-3 code
- ISO 639-3 Codes for the representation of names of languages — Part 3: Alpha-3 code for comprehensive coverage of languages
- ISO 639-5 Codes for the representation of names of languages — Part 5: Alpha-3 code for language families and groups
ISO/IEC 646 internationalized 7 bit ASCII variants
ISO 657 Hot-rolled steel sections
ISO 668 Specification for Shipping Containers
ISO 690 bibliographic references
ISO 704 Terminology work - Principles and methods
ISO 732 Photography — 120-size and 220-size films — Dimensions
ISO 764 Horology — Magnetic resistant watches
ISO 838 Standard for punching filing holes into paper
ISO 843:1997 Conversion of Greek characters into Roman characters
ISO 860 Terminology work -- Harmonization of concepts and terms
ISO 898 Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel
- ISO 898-1 Bolts, screws and studs with specified property classes—Coarse thread and fine pitch thread
- ISO 898-2 Nuts with specified proof load values—Coarse thread
- ISO 898-5 Set screws and similar threaded fasteners not under tensile stresses
- ISO 898-6 Nuts with specified proof load values—Fine pitch thread
- ISO 898-7 Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
ISO 965 General purpose metric screw threads — Tolerances
- ISO 965-1 Principles and basic data
- ISO 965-2 Limits of sizes for general purpose external and internal screw threads.
- ISO 965-3 Deviations for constructional screw threads
- ISO 965-4 Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
- ISO 965-5 Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
ISO 999 Guidelines for the content, organization, and presentation of indexes

[edit] ISO 1000–ISO 9999

ISO 1000 SI units and recommendations for the use of their multiples and of certain other units
ISO 1004 Magnetic ink character recognition
ISO 1007 135 film format
ISO 1028 Information processing - Flowchart symbols
ISO/IEC 1539 Fortran programming language
ISO 1629 Establishes a system of terms and nomenclature for polymers
ISO 1745 Information processing — Basic mode control procedures for data communication systems
ISO 1750 Pesticides and other agrochemicals — Common names
ISO 1789 Medical vehicles and their equipment. Road ambulances
ISO/IEC 2022 Information technology: Character code structure and extension techniques
ISO 2108 International standard book numbering (ISBN)
ISO 2145 Numbering of divisions and subdivisions in written documents
ISO 2162 Technical product documentation -- Springs -- Part 1: Simplified representation
ISO 2171 Cereals and milled cereal products — Determination of total ash
ISO 2242 Photography -- Light sources for use in sensitometric exposure -- Simulation of the spectral distribution of photoflood illumination
ISO 2281 Water-resistant watches
ISO 2533 Standard Atmosphere
ISO 2636 Information processing — Conventions for incorporating flowchart symbols in flowcharts
ISO 2709 Format for information exchange (e.g. MARC)
ISO 2768 Standard for dimensional tolerance in manufacturing
ISO 3029 126 film format
ISO 3082 Iron ores — Sampling and sample preparation procedures
ISO 3098 Technical product documentation -- Lettering -- Part 0: General requirements
ISO 3103 Method of brewing tea for the purpose of sensory tests
ISO 3166 codes for countries and subdivisions
- ISO 3166-1 codes for country and dependent area names, first published in 1974
  - ISO 3166-1 alpha-2 two-letter country codes
  - ISO 3166-1 alpha-3 three-letter country codes
  - ISO 3166-1 numeric
- ISO 3166-2 principal subdivisions of a country or dependent area.
- ISO 3166-3 superseded ISO 3166-1 codes, first published in 1998.
ISO 3297 International standard serial number (ISSN)
ISO 3506 Mechanical properties of corrosion-resistant stainless steel fasteners.
ISO 3536 Road vehicles — Safety glazing materials — Vocabulary
ISO 3537 Road vehicles — Safety glazing materials — Mechanical tests
ISO 3538 Road vehicles — Safety glazing materials — Method for the determination of solar transmittance
ISO 3601 Fluid power systems — O-rings
- ISO 3601-1 Inside diameters, cross-sections, tolerances and size identification code (Recently updated)
- ISO 3601-2 Housing dimensions for general applications (Recently updated)
- ISO 3601-4 Anti-extrusion rings (back-up rings) (Recently updated)
ISO 3602 Romanization of Japanese
ISO 3632 Quality of Saffron
ISO 3635:1981 Size designation of clothes — Definitions and body measurement procedure
ISO 3864 Safety labels
ISO 3901 International Standard Recording Code (ISRC)
ISO 3977 Design and procurement standards for gas turbine system applications
ISO 4074: Natural latex rubber condoms -- Requirements and test methods
ISO 4157 Subdivision of construction works
- ISO 4157-1: buildings and part of buildings
- ISO 4157-2: room numbers
- ISO 4157-3: room identifiers
ISO 4179 Ductile iron pipes and fittings for pressure and non-pressure pipelines — Cement mortar lining
ISO 4217 Currency codes
ISO 4628 Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance
- ISO 4628-1 : General introduction and designation system
- ISO 4628-3 : Assessment of degree of rusting
ISO/IEC 4873:1991 8-bit code for information interchange
ISO 4892 Plastics -- Methods of exposure to laboratory light sources
ISO 5167 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full
- ISO 5167-1 Part 1: General principles and requirements
- ISO 5167-2 Part 2: Orifice plates
- ISO 5167-3 Part 3: Nozzles and Venturi nozzles
- ISO 5167-4 Part 4: Venturi tubes
ISO 5218 Representation of human sexes
ISO 5455 Technical drawings: scales
ISO 5457 Technical product documentation -- Sizes and layout of drawing sheets
ISO 5775 Bicycle tires and rims
ISO 5800 Photographic Film speed
ISO 5964 Guidelines for the Establishment and Development of Multilingual Thesauri
ISO 5971:1981 Size designation of clothes — Pantyhose
ISO 6166 structure of an International Securities Identifying Number (ISIN)
ISO 6194 Rotary-shaft lip-type seals incorporating elastomeric sealing elements
- ISO 6194-5 Identification of visual imperfections
ISO 6344 Coated abrasives — Grain size analysis
- ISO 6344-1 Part 1: Grain size distribution test
- ISO 6344-2 Part 2: Determination of grain size distribution of macrogrits P12 to P220
- ISO 6344-3 Part 3: Determination of grain size distribution of microgrits P240 to P2500
ISO 6336 Calculations for life and strength of Gears
ISO 6429 Information technology: Control functions for coded character sets
ISO 6438 Documentation — African coded character set for bibliographic information interchange
ISO 6579 Microbiological detection of Salmonella spp in food and animal feeding stuffs.
ISO 6594 Cast iron drainage pipes and fittings — Spigot series
ISO 6709 Standard representation of latitude, longitude and altitude for geographic point locations
ISO 6946 Building components and building elements — Thermal resistance and thermal transmittance — Calculation method
ISO 7001 Public Information Symbols
ISO 7002 Agricultural food products — Layout for a standard method of sampling from a lot
ISO 7098 Romanization of Chinese
ISO 7200 Technical product documentation - Data fields in title blocks and document headers
ISO 7372 Trade data interchange
ISO/IEC 7501-1:1997 Identification cards — Machine readable travel documents (Part 1: Machine readable passport; Part 2: Machine readable visa; Part 3: Machine readable official travel documents)
ISO 7736 Car radio installation space
ISO/IEC 7810 Identification cards — Physical characteristics
ISO/IEC 7811 Identification cards — Recording technique
ISO/IEC 7812 Identification cards — Identification of issuers
ISO/IEC 7813 Information technology — Identification cards — Financial transaction cards
ISO/IEC 7816 Identification cards — Integrated circuit cards
ISO/IEC 7942 Graphical Kernel System
ISO 8000 Data quality
ISO 8090 Cycles — Terminology
ISO 8180 Ductile iron pipelines — Polyethylene sleeving for site application
ISO 8373 Manipulating Industrial Robots — Vocabulary
ISO 8402 Quality Management and Quality Assurance — Vocabulary
ISO 8501-1 Preparation of steel substrates before application of paints and related products
ISO 8555 Environmental management systems.
ISO 8559:1989 Garment construction and anthropometric surveys — Body dimensions
ISO 8583 Financial transaction card originated messages — Interchange message specifications
- ISO 8583-1 Part 1: Messages, data elements and code values
- ISO 8583-2 Part 2: Application and registration procedures for Institution Identification Codes (IIC)
- ISO 8583-3 Part 3: Maintenance procedures for messages, data elements and code values
ISO 8601 Data elements and interchange formats — Information interchange — Representation of dates and times
ISO/IEC 8613 Open Document Architecture
ISO/IEC 8632 Computer Graphics Metafile
ISO 8651 Graphical Kernel System language bindings
ISO/IEC 8652: Information technology — Programming languages — Ada
ISO 8653:1986 Jewellery — Ring-sizes — Definition, measurement and designation
ISO 8805 Graphical Kernel System for Three Dimensions and the C language bindings are ISO 8806.
ISO 8806-4 Graphical Kernel System for Three Dimensions, C language bindings
ISO 8807: Language Of Temporal Ordering Specification (LOTOS)
ISO/IEC 8824 Abstract Syntax Notation One (ASN.1)
ISO/IEC 8825 ASN.1 Encoding Rules
ISO 8859 8-bit coded character sets
- ISO 8859-1 Latin-1
- ISO 8859-2 Latin-2
- ISO 8859-3 Latin-3 or "South European"
- ISO 8859-4 Latin-4 or "North European"
- ISO 8859-5 Cyrillic
- ISO 8859-6 Arabic
- ISO 8859-7 Greek
- ISO 8859-8 Hebrew
- ISO 8859-9 Latin-5
- ISO 8859-10 Latin-6, rearrangement of 8859-4
- ISO 8859-11 Thai
- ISO 8859-13 Latin-7 or "Baltic Rim"
- ISO 8859-14 Latin-8 or "Celtic"
- ISO 8859-15 Latin-9, revision of 8859-1
- ISO 8859-16 Latin-10 South-Eastern European languages and others
ISO 8879 Standard Generalized Markup Language (SGML)
ISO 9000 Quality management system in production environments
ISO 9001 Quality management
ISO 9069 SGML support facilities — SGML Document Interchange Format (SDIF)
ISO/IEC 9075 SQL
ISO/IEC 9126 Software engineering — Product quality
ISO 9141 Network interconnection of computers in a vehicle
- ISO 9141-2 OBD-II standard, aka 9141 CARB standard
ISO 9241 Ergonomic requirements for office work with visual display terminals
ISO 9362 Bank Identifier Code or BIC system
ISO 9407 Shoe sizes
ISO/IEC 9541 Information technology — Font information interchange
- ISO/IEC 9541-1:1991 Information technology — Font information interchange — Part 1: Architecture
- ISO/IEC 9541-2:1991 Information technology — Font information interchange — Part 2: Interchange Format
- ISO/IEC 9541-3:1994 Information technology — Font information interchange — Part 3: Glyph shape representation
ISO 9564 Banking — Personal Identification Number (PIN) management and security (in ATM and POS systems)
ISO/IEC 9579 Remote database access for SQL
ISO 9592, ISO 9593 PHIGS (Programmer's Hierarchical Interactive Graphics System)
ISO/IEC 9594 Information technology — Open Systems Interconnection — The Directory
ISO 9660 Information processing — Volume and file structure of CD-ROM for information interchange
ISO/IEC 9796 Information technology — Security techniques — Digital signature schemes giving message recovery
ISO/IEC 9797 Information technology — Security techniques — Message Authentication Codes (MACs)
ISO/IEC 9798 Information technology — Security techniques — Entity authentication
ISO/IEC 9834 Information technology — Open Systems Interconnection — Procedures for the operation of OSI Registration Authorities
ISO 9869 Thermal insulation — Building elements — In-situ measurements of thermal resistance and thermal transmittance
ISO 9899 C programming language
ISO/IEC 9945 Portable Operating System Interface (POSIX)
ISO 9984 Conversion of Georgian characters into Roman characters
ISO 9985 Conversion of Armenian characters into Roman characters
ISO 9992:1999 Financial transaction cards — Security architecture of financial transaction systems using integrated circuit cards
ISO 9999 Technical aids for persons with disabilities. Classification and terminology

[edit] ISO 10000–ISO 19999

ISO 10006 Quality management — Guidelines to quality in project management
ISO 10007 Quality management — Guidelines for configuration management
ISO 10012 Measurement management systems — Requirements for measurement processes and measuring equipment
ISO/IEC 10021 Message Oriented Text Interchange Systems (MOTIS)
ISO/IEC 10026 Open Systems Interconnection
ISO 10077 Thermal performance of windows, doors and shutters — Calculation of thermal transmittance
ISO/IEC 10089 Information technology; 130 mm rewritable optical disk cartridge for information interchange — 650 MB per cartridge
ISO 10160 Interlibrary Loan Application Service Definition — defines terminology used in interlibrary loan
ISO 10161 Interlibrary Loan Application Protocol
ISO/IEC 10164 Information technology -- Open Systems Interconnection -- ???
ISO/IEC 10179:1996 Document Style Semantics and Specification Language (DSSSL)
ISO 10202:1991 Financial transaction cards — Security architecture of financial transaction systems using integrated circuit cards
ISO 10206 Extended Pascal (programming language)
ISO 10211 Thermal bridges in building construction — Heat flows and surface temperatures — Detailed calculations
ISO 10279 BASIC programming language
ISO 10303 Industrial automation systems and integration — Product data representation and exchange. Known as STEP, STandard for the Exchange of Product data
ISO 10383 Securities and related financial instruments — Codes for exchanges and market identification (MIC)
ISO 10487 Connections for passenger car stereos
ISO 10628 Flow diagrams for process plants
ISO 10646 Universal Character Set (equivalent to Unicode's character set)
ISO 10664 Hexalobular internal driving feature for bolts and screws — Torx screw head
ISO 10957 Information and documentation — International Standard Music Number (ISMN)
ISO 10962 Securities and related financial instruments — Classification of Financial Instruments (CFI code)
ISO 10993 Biological Evaluation of medical devices
- ISO 10993-1:2008 Evaluation and testing within a risk management system
- ISO 10993-2: Animal welfare requirements.
- ISO 10993-3: tests for genotoxicity, carcinogenicity and reproductive toxicity.
- ISO 10993-4: Selection of tests for interactions with blood.
- ISO 10993-5: Test for in vitro cytotoxicity
- ISO 10993-6:2007 Tests for local effects after implantation.
- ISO 10993-7:2008 Ethylene oxide sterilization residuals
- ISO 10993-8:
- ISO 10993-9:2007 Framework for identification and quantification of potential degradation products.
- ISO 10993-10: Tests for irritation and sensitisation
- ISO 10993-11: Tests for irritation systemic toxicity
- ISO 10993-12:2007 Sample preparation and reference materials.
- ISO 10993-13: Identification and Quantification of degradation products from polymeric medical devices.
- ISO 10993-14: Identification and Quantification of degradation products from ceramics.
- ISO 10993-15: Identification and quantification of degradation products from un-coated or coated metals and alloys.
- ISO 10993-16: Toxicokinetic study design for degradation products and leachables.
- ISO 10993-17: Methods for the establishment of allowable limits for leachable substances using health-based risk assessment.
- ISO 10993-18: Chemical characterisation of materials.
- ISO 10993-19: Physico-chemical, morphological and topographical characterization of materials
- ISO 10993-20:2006 Principles and methods for immunotoxicology testing of medical devices
ISO 11064 Ergonomic Design of Control Centres
- ISO 11064-1:2000 Part 1: Principles for the design of control centres
- ISO 11064-2:2000 Part 2: Principles for the arrangement of control suites
- ISO 11064-3:1999 Part 3: Control room layout ISO 11064-3:1999/Cor 1:2002
- ISO 11064-4:2004 Part 4: Layout and dimensions of workstations
- ISO 11064-5:2008 Part 5: Displays and controls
- ISO 11064-6:2005 Part 6: Environmental requirements for control centres
- ISO 11064-7:2006 Part 7: Principles for the evaluation of control centres
ISO/IEC 11172 MPEG-1
ISO 11170:2003 Hydraulic fluid power — Filter elements — Sequence of tests for verifying performance characteristics
ISO/IEC 11179 Information Technology — Metadata Registries (MDR)
- ISO/IEC 11179-1:2004 Part 1: Framework
- ISO/IEC 11179-2:2005 Part 2: Classification
- ISO/IEC 11179-3:2003 Part 3: Registry metamodel and basic attributes
- ISO/IEC 11179-4:2004 Part 4: Formulation of data definitions
- ISO/IEC 11179-5:2005 Part 5: Naming and identification principles
- ISO/IEC 11179-6:2005 Part 6: Registration
ISO 11180 Postal addressing
ISO/IEC 11404:1996 Language-independent datatypes (See also General purpose datatypes)
ISO 11446:2004 Connectors for the electrical connection of towing and towed vehicles — 13-pole connectors for vehicles with 12 V nominal supply voltage
ISO 11469:2000 Plastics — Generic identification and marking of plastics products
ISO 11521 Replaced by ISO 15022
ISO/IEC 11578:1996 Information technology — Open Systems Interconnection — Remote procedure call (RPC)
ISO 11783 aka. IsoBus — J1939-based communication protocol for the agriculture industry.
ISO/IEC 11801 Information technology — Generic cabling for customer premises
ISO 11898 Road vehicles — Controller area network (CAN)
ISO 12006 Building construction. Organization of information about construction works.
ISO 12207 Software lifecycle processes.
ISO 12639 Graphic technology — Prepress digital data exchange — Tag image file format for image technology (TIFF/IT)
ISO 12641 Graphic technology — Prepress digital data exchange — Colour targets for input scanner calibration
ISO 13239 High-level data link control (HDLC) procedures
ISO/IEC 13249 SQL multimedia and application packages
ISO/IEC 13250 Topic map
ISO 13346 Volume and file structure of write-once and rewritable media, which UDF is based on.
ISO 13370 Thermal performance of buildings — Heat transfer via the ground — Calculation methods
ISO 13406 Ergonomic requirements for work with visual displays based on flat panels
- ISO 13406-1:1999 Part 1: Introduction
- ISO 13406-2:1002 Part 2: Ergonomic requirements for flat panel displays
ISO 13407:1999 Human-centred design processes for interactive systems
ISO 13450 110 film format
ISO 13485:2003 Medical Devices — Quality management systems — Requirements for regulatory purposes.
ISO 13490 Information technology: Volume and file structure of read-only and write-once compact disk media for information interchange
ISO 13567/1 to 3 Technical product documentation; Organization and naming of layers for Computer-aided design (CAD)
ISO/IEC 13568:2002 Information Technology — Z Formal Specification Notation — Syntax, Type System and Semantics
ISO 13616 Bank Account Numbers (IBAN
ISO 13628 - Design And Operation Of Subsea Production Systems
- ISO 13628-1 - Part 1: General Requirements And Recommendations
- ISO 13628-2 - Part 2: Unbonded Flexible Pipe Systems For Subsea And Marine
- ISO 13628-3 - Part 3: Through flowline (TFL) systems
- ISO 13628-4 - Part 4: Subsea wellhead and tree equipment
- ISO 13628-5 - Part 5: Subsea Umbilicals
- ISO 13628-6 - Part 6: Subsea Production Control Systems
- ISO 13628-7 - Part 7: Completion/workover Riser Systems
- ISO 13628-8 - Part 8: Remotely Operated Vehicle (rov) Interfaces On Subsea
- ISO 13628-9 - Part 9: Remotely Operated Tool (rot) Intervention Systems
- ISO 13628-10 - Part 10: Specification For Bonded Flexible Pipe
- ISO 13628-11 - Part 11: Flexible Pipe Systems for Subsea and Marine Applications
ISO 13849-1 Safety of machinery, Safety related parts of control systems, General principles for design
ISO/IEC 13818 MPEG-2
ISO 13837 Road vehicles — Safety glazing materials — Method for the determination of solar transmittance
ISO 14000 Environmental Management Standards in production environments
ISO 14001 Environmental Management
ISO 14064 Greenhouse Gases
ISO 14223 Radiofrequency [sic] identification of animals — Advanced transponders
ISO 14230 Road vehicles — Diagnostic systems — Keyword Protocol 2000
- ISO 14230-1 Physical layer
- ISO 14230-2 Data link layer
- ISO 14230-3 Application layer
- ISO 14230-4 Requirements for emission-related systems
ISO/IEC 14443 Identification cards — Contactless integrated circuit(s) cards — Proximity cards
ISO/IEC 14496 MPEG-4
ISO 14644 Standards Cleanrooms and associated controlled environments
- ISO 14644-1:1999 Classification of Air Cleanliness
- ISO 14644-2:2000 Testing and Monitoring to prove Compliance
- ISO 14644-3:2005 Metrology & Test Methods
- ISO 14644-4:2001 Design, Construction and Start-up
- ISO 14644-5:2004 Operations
- ISO 14644-6:2007 Vocabulary
- ISO 14644-7:2004 Separative Devices
- ISO 14644-8:2006 Classification of Airborne Molecular Contamination
- ISO 14644-9 Clean Surfaces
ISO 14651 Information technology: International string ordering and comparison
ISO 14698 Standards
- ISO-14698-1 Bio-contamination Control — General Principles
- ISO-14698-2 Evaluation & Interpretation of Bio-contamination Data
ISO 14750 Information technology — Open Distributed Processing — Interface Definition Language
ISO/IEC 14755 Input methods to enter unicode characters from ISO/IEC 10646
ISO 14855-1:2005 Aerobic Biodegradation under controlled composting conditions
ISO 14855-2:2007 Aerobic Biodegradation under controlled composting conditions with gravimetric measurement of carbon dioxid
ISO/IEC 14882 Programming Languages — C++
ISO 14915 Software ergonomics for multimedia user interfaces
- ISO 14915-1:2002 Part 1: Design principles and framework
- ISO 14915-2:2003 Part 2: Multimedia navigation and control
- ISO 14915-3:2002 Part 3: Media selection and combination
ISO 14971:2007 Medical Devices — Application Of Risk Management To Medical Devices
ISO/IEC 14977 Extended Backus-Naur Form (EBNF)
ISO 15000 Electronic business eXtensible Markup Language ebXML
- ISO 15000-1:2004 Part 1: Collaboration-protocol profile and agreement specification (ebCPP)
- ISO 15000-2:2004 Part 2: Message service specification (ebMS)
- ISO 15000-3:2004 Part 3: Registry information model specification (ebRIM)
- ISO 15000-4:2004 Part 4: Registry services specification (ebRS)
- ISO 15000-5:2005 Part 5: ebXML Core Components Technical Specification, Version 2.01(ebCCTS)
ISO 15022 Securities: Scheme for messages(Data Field Dictionary)
ISO 15082 Road vehicles — Tests for rigid plastic safety glazing materials
ISO 15099 Thermal performance of windows, doors and shading devices — Detailed calculations
ISO 15112 Natural gas — Energy determination
ISO 15189 Medical laboratories — Particular requirements for quality and competence
ISO 15288 Systems engineering — System life cycle processes
ISO 15289 Systems and software engineering — Content of systems and software life cycle process information products (Documentation)
ISO/IEC 15291: Information technology — Programming languages — Ada Semantic Interface Specification (ASIS)
ISO 15403 Natural gas — Natural gas for use as a compressed fuel for vehicles
- ISO 15403-1 Designation of the quality
ISO/IEC 15408 Common Criteria — Evaluation Criteria for Information Technology Security
ISO/IEC 15434 Information technology — Automatic Identification and Data Capture Techniques - Syntax for High-Capacity ADC Media. For example: Data Matrix 2D barcode
ISO/IEC 15444 JPEG 2000
ISO/IEC 15445:2000 ISO HTML, a subset of Hypertext Markup Language (HTML) 4
ISO/IEC 15504 Framework for the assessment of software processes, also known as SPICE (Software Process Improvement and Capability Determination).
ISO 15614-13:2002 Specification and qualification of welding procedures for metallic materials-Welding procedure test
ISO 15686 Service life planning for constructive works in 10 parts
ISO/IEC 15693 Identification cards — Contactless integrated circuit(s) cards — Vicinity cards
ISO 15706 International Standard Audiovisual Number
ISO 15707 International Standard Musical Work Code
ISO 15836 The Dublin Core metadata element set
ISO 15897 Standard for the registration of new POSIX locales and POSIX charmaps
ISO 15924 Codes for the representation of names of scripts
ISO 15930 Graphic technology — Prepress digital data exchange using PDF
ISO/IEC 15948:2003 Portable Network Graphics (PNG)
ISO 15970 Natural gas — Measurement of properties — Volumetric properties: density, pressure, temperature and compression factor
ISO 15971 Natural gas. Measurement of properties. Calorific value and Wobbe index
ISO/IEC 16500 Generic Digital Audio-Visual Systems DAVIC
ISO 16071:2003 Ergonomics of human-system interaction, Guidance on accessibility for human-computer interfaces
ISO 16134 Earthquake- and subsidence-resistant design of ductile iron pipelines
ISO 16232 Road vehicles — Cleanliness of components of fluid circuits
- ISO 16232-8 Particle nature determination by microscopic analysis
- ISO 16232-9 Particle sizing and counting by automatic light extinction particle counter
- ISO 16232-10 Expression of results
ISO/IEC 16262 ECMAScript
ISO 16549 Textiles — Unevenness of textile strands — Capacitance method
ISO 16750 Road vehicles — Environmental conditions and testing for electrical and electronics equipment.
ISO/TS 16949 Quality management systems — Particular requirements for the application of ISO 9001:2000 for automotive production and relevant service part organizations
ISO 16982:2002 Ergonomics of human-system interaction, Usability methods supporting human-centred design
ISO/IEC 17020:1998 General criteria for the operation of various types of bodies performing inspection
ISO/IEC 17024:2003 specifies requirements for a body certifying persons against specific requirements, including the development and maintenance of a certification scheme for personnel
ISO/IEC 17025 General requirements for competence of test and calibration laboratories
ISO 17202 Textiles — Determination of twist in single spun yarns — Untwist/retwist method
ISO 17776 : Petroleum industries
ISO/IEC 17799 Information technology: Code of practice for information security management
ISO/IEC 17894 Ships and marine technology — Computer applications — General principles for development and use of PES in marine applications
ISO/IEC 18000 Information Technology AIDC Techniques-RFID (Radio Frequency Identification) for Item Management — Air Interface
- 18000-1 Part 1 — Generic Parameters for the Air Interface for Globally Accepted Frequencies
- 18000-2 Part 2 — Parameters for Air Interface Communications below 135 kHz
- 18000-3 Part 3 — Parameters for Air Interface Communications at 13.56 MHz
- 18000-4 Part 4 — Parameters for Air Interface Communications at 2.45 GHz
- 18000-5 Part 5 — Parameters for Air Interface Communications at 5.8 GHz (Withdrawn)
- 18000-6 Part 6 — Parameters for Air Interface Communications at 860 to 960 MHz
- 18000-7 Part 7 — Parameters for Air Interface Communications at 433 MHz
ISO/IEC 18004: QR Code Standardization
ISO/IEC 18009: Information technology — Programming languages — Ada: Conformity assessment of a language processor (ACATS)
ISO/IEC 18013 Information technology — Personal Identification — ISO-compliant driving license
- ISO/IEC 18013-1:2005(E) Part 1: Physical characteristics and basic data set
- ISO/IEC 18013-2:2008(E) Part 2: Machine-readable technologies
- ISO/IEC 18013-3:2009(E) Part 3: Access control, authentication and integrity validation
ISO/IEC 18014 Information technology — Security techniques — Time-stamping services
ISO/IEC 18023:2006(E) Information technology — SEDRIS —
- ISO/IEC 18023-1:2006(E) Information technology — SEDRIS — Part 1: Functional specification
- ISO/IEC 18023-2:2006(E) Information technology — SEDRIS — Part 2: Abstract transmittal format
- ISO/IEC 18023-3:2006(E) Information technology — SEDRIS — Part 3: Transmittal format binary encoding
ISO/IEC 18024-4:2006(E) Information technology — SEDRIS language bindings — Part 4: C
ISO/IEC 18025:2005(E) Information technology — Environmental Data Coding Specification
(EDCS)
ISO/IEC 18026:2006(E) Information technology — Spatial Reference Model
(SRM)
ISO/IEC 18033 Information technology — Security techniques — Encryption algorithms
- Part 1: General
- Part 2: Asymmetric ciphers
- Part 3: Block ciphers
- Part 4: Stream ciphers
ISO/IEC 18041-4:2005(E) Information technology — EDCS language bindings — Part 4: C
ISO/IEC 18042-4:2006(E) Information technology — Spatial Reference Model (SRM) language bindings — Part 4: C
ISO 18152:2003 Ergonomics of human-system interaction, Specification for the process assessment of human-system issues
ISO 18185: Wireless standard for electronic seals using active RFID (Radio Frequency Identification)
ISO 18245 standard concerning the assignment of Merchant Category Codes (MCC) in retail financial services
ISO 18529:2000 Ergonomics of human-system interaction, Human-centred lifecycle process descriptions (available in English only)
ISO 18629 standardized Process Specification Language (PSL).
ISO 19005 Document management — Electronic document file format for long-term preservation
ISO 19011 standard providing guidelines for quality and environmental management systems auditing
ISO 19092-1 Financial Services — Security — Part 1: Security framework
ISO 19092-2 Financial Services — Security — Part 2: Message syntax and cryptographic requirements
ISO 19101 Geographic Information: Reference model
ISO 19105 Geographic Information: Conformance and testing
ISO 19107 Geographic Information: Spatial schema
ISO 19108 Geographic Information: Temporal schema
ISO 19109 Geographic Information: Rules for Application Schema
ISO 19110 Geographic Information: Feature cataloguing methodology
ISO 19111 Geographic Information: Spatial referencing by coordinates
ISO 19111 Geographic Information: Spatial referencing by identifier
ISO 19113 Geographic Information: Quality principles
ISO 19114 Geographic Information: Quality evaluation procedures
ISO 19115 Geographic Information: Metadata
ISO 19123 Geographic Information: Coverage schema
ISO 19128 Geographic Information: Web Map Service
ISO 19131 Geographic Information: Data product specification
ISO 19136 Geographic Information: Geography Markup Language
ISO 19439 Framework for enterprise modelling
ISO 19440 Constructs for enterprise modelling
ISO/IEC 19501 Unified Modeling Language (UML)
ISO/IEC 19502 Meta-Object Facility (MOF)
ISO/IEC 19503 XML Metadata Interchange (XMI)
ISO/IEC 19757 Document Schema Definition Languages (DSDL)
- ISO/IEC FDIC 19757-2 Regular-grammar-based validation RELAX NG
- ISO/IEC 19757-3 Rule-based validation — Schematron
- ISO/IEC 19757-4 Namespace-based Validation Dispatching Language (NVDL)
ISO/IEC 19770 Information technology — Software asset management
ISO/IEC 19785 Common Biometric Exchange Formats Framework (CBEFF 2.0)
ISO/IEC 19790 Security requirements for cryptographic modules (see also FIPS 140)
ISO/IEC 19794 Information technology — Biometric data interchange formats
- ISO/IEC 19794-1:2006 Part 1: Framework
- ISO/IEC 19794-2:2005 Part 2: Finger minutiae data
- ISO/IEC 19794-3:2006 Part 3: Finger pattern spectral data
- ISO/IEC 19794-4:2005 Part 4: Finger image data
- ISO/IEC 19794-5:2005 Part 5: Face image data
- ISO/IEC 19794-6:2005 Part 6: Iris image data
- ISO/IEC 19794-7:2007 Part 7: Signature/sign time series data
- ISO/IEC 19794-8:2006 Part 8: Finger pattern skeletal data
- ISO/IEC 19794-9:2007 Part 9: Vascular image data
- ISO/IEC 19794-10:2007 Part 10: Hand geometry silhouette data

[edit] ISO 20000–ISO 29999

ISO/IEC 20000:2005 IT Service Management System (based on BS15000)
ISO 20022 Financial Services — universal financial industry message scheme
ISO/IEC TR 20943 Information technology — Procedures for achieving metadata registry content consistency
- ISO/IEC TR 20943-1:2003 Part 1: Data elements
- ISO/IEC TR 20943-3:2004 Part 3: Value domains
ISO 21482 Ionizing-radiation warning -- Supplementary symbol
ISO 22000 Food safety management systems — Requirements for any organization in the food chain
- ISO/TS 22003 Food safety management systems — Requirements for bodies providing audit and certification of food safety management systems
ISO 22093 Industrial automation systems and integration -- Physical device control -- Dimensional Measuring Interface Standard (DMIS)
ISO 22241 : Diesel engines — NOx reduction agent AUS 32
- ISO 22241-1 : Quality requirements
- ISO 22241-2 : Test methods
- ISO 22241-3 : Handling, transportation and storing
ISO/IEC TR 22250 Regular Language description for XML — (RELAX)
- ISO/IEC TR 22250-1:2002 RELAX Core
ISO/PAS 22399:2007 Social security — Guideline for incident preparedness and operational continuity management
ISO 22716:2007: Cosmetics.
ISO/IEC 23003-1 : MPEG Surround (aka MPEG-D)
ISO/IEC 23270:2003 C# Programming Language
ISO/IEC 23360 Linux Standard Base (LSB) core specification 3.1 (in publication as of 2005-12)
- ISO/IEC 23360-1 — Part 1: Generic specification
- ISO/IEC 23360-2 — Part 2: Specification for IA32 architecture
- ISO/IEC 23360-3 — Part 3: Specification for IA64 architecture
- ISO/IEC 23360-4 — Part 4: Specification for AMD64 architecture
- ISO/IEC 23360-5 — Part 5: Specification for PPC32 architecture
- ISO/IEC 23360-6 — Part 6: Specification for PPC64 architecture
- ISO/IEC 23360-7 — Part 7: Specification for S390 architecture
- ISO/IEC 23360-8 — Part 8: Specification for S390X architecture
ISO 23733 Textiles — Chenille yarns — Test method for the determination of linear density
ISO 23950 Library standard ANSI/NISO Z39.50 — Protocol for searching and retrieving information, usually from bibliographic records
ISO/IEC 24727 Identification cards — Integrated circuit card programming interfaces
- ISO/IEC 24727-1 — Part 1: Architecture
- ISO/IEC 24727-2 — Part 2: Generic card interface
- ISO/IEC 24727-3 — Part 3: Application interface
- ISO/IEC 24727-4 — Part 4: Application programming interface (API) administration
- ISO/IEC CD 24727-5 — Part 5: Testing
- ISO/IEC FCD 24727-6 — Part 6: Registration authority procedures for the authentication protocols for interoperability
ISO/IEC 24744:2007 Software Engineering — Metamodel for Development Methodologies
ISO/IEC 24762:2008 Information technology — Security techniques — Guidelines for information

and communications technology disaster recovery services

ISO/IEC DIS 25961 Recommended Practice for Architectural Description of Software-Intensive Systems. See IEEE 1471
ISO26000 Guideline about Social Responsibility also called ISO SR
ISO/IEC 26300 OpenDocument Format (ODF)
ISO/IEC 27000-series Information security management system family of standards
- ISO/IEC 27000 Information security management systems — Overview and vocabulary
- ISO/IEC 27001 Information security management systems — Requirements
- ISO/IEC 27002 Code of practice for information security management
- ISO/IEC 27003 Information security management system implementation guidance
- ISO/IEC 27004 Information security management — Measurement
- ISO/IEC 27005 Information security risk management
- ISO/IEC 27006 Requirements for bodies providing audit and certification of information security management systems
- ISO/IEC 27007 Guidelines for information security management systems auditing
- ISO/IEC 27011 Information security management guidelines for telecommunications organizations based on ISO/IEC 27002
ISO/PAS 28000 - Specification for security management systems for the supply chain
- ISO/PAS 28004 - Guidelines for the implementation of ISO/PAS 28000
ISO/IEC 29119 Software Testing^[4]
- ISO/IEC 29119-1 — Part 1: Concepts & Vocabulary
- ISO/IEC 29119-2 — Part 2: Test Process
- ISO/IEC 29119-3 — Part 3: Test Documentation
- ISO/IEC 29119-4 — Part 4: Test Techniques
ISO/IEC 29500 Office Open XML
- ISO/IEC 29500-1 — Part 1: Fundamentals and Markup Language Reference
- ISO/IEC 29500-2 — Part 2: Open Packaging Conventions
- ISO/IEC 29500-3 — Part 3: Markup Compatibility and Extensibility
- ISO/IEC 29500-4 — Part 4: Transitional Migration Features

ISO 30000–ISO 39999

ISO 31000 Risk management
ISO 32000 Document management — Portable document format
ISO/IEC 38500 Corporate governance of information technology

ISO 80000

ISO/IEC 80000 Quantities and units

References

Other Standards

2010-05-27T07:01:00.000-07:00

Standards
AS 9000
ISO 9001
ISO/TS 16949
QS 9000
ISO 13485
SS 524
ISO 17025
ISO 14001
ISO 22000
HACCP
SS444
SA 8000
ISO 27001
ISMS-ISO 17799
BS 7799
OHSAS 18001
SMC
SCC
SS 506
CP 79

ISO 9001:2008 Upgrading - online service
Upgrade your ISO 9001 Documentation
to meet the NEW version of the standard
with out leaving your desk

ISO 18001:2007 Upgrading - online service
Upgrade your OHSAS Documentation to
meet the NEW version of the standard
with out leaving your desk

OHSAS 18001

2010-05-27T06:42:00.000-07:00

ISO 18001:2007 Upgrading - online service
Now you can upgrade your OHSAS 18001 Documentation
to meet requirements of NEW version of the standard
with out leaving your desk.
How It Works?
Make payment (Select the Standard and click "Add to Cart" button on the right corner of this
page). Email us your payment receipt number and soft copy of your OHSAS 18001 Documents
in EDITABLE text format (e.g Microsoft WORD or EXCEL files). We will amend and email back
your documents to meet the requirements of new version of the standard OHSAS 18001:2007.
Can we make Cheque payments or through other means?
Yes, you can pay through Bank cheques or other means. Email us to work out a payment
method suitable for you.
How long it takes to upgrade?If you send us your OHSAS 18001 Documents in EDITABLE text format (e.g Microsoft WORD or
EXCEL files, it takes 10 (Ten) working days to revise and send back your documents. Count 7
days from the date you have sent the complete set of documents and payment.
How much it cost to upgrade on line?S$800 (Singapore Dollars Eight Hundreds Only), if you send us your OHSAS 18001 Documents
in EDITABLE text format (e.g Microsoft WORD or EXCEL files).
From which country we can use this online upgrading service?You can use this online service from any country or region or part of the world.
Is it possible to interact or communicate or talk with the consultant who is handling our
project?Yes, you can interact or communicate or talk with the consultant through phone, fax, email or
chat on msn or yahoo or skype.
We do not have editable text files for our OHSAS 18001 documents, we only have printed
copy, can we still use this online upgrading service?Yes, you can use our online upgrading service if you only have printed copies. You can send us
scanned copies as pdf or tiff files or courier your printed copies to us. But there will be
additional charges to convert your pdf or tiff files or printed copies to Microsoft WORD or EXCEL
files). Contact us through email or phone or fax for a quotation.
What are the documents we need to send?You need to send the following documents for us to completely upgrade:
Safety Policy Statements
Safety Objectives
Safety Manual
Safety Procedures
Emergency Response Plans
Management Programme
Copy of Local Health and Safety Regulations
Material safety Data Sheets
Risk Assessment records, Risk Control plans
Standard Forms
Our OHSAS 18001 is integrated with ISO 9001, can we still use this online upgrading
service?
Yes, Integrated OHSAS 18001 & ISO 9001 documents can be upgraded. Pay for both Standards
and send the payment receipt numbers and the integrated OHSAS 18001 & ISO 9001
documents.
Our OHSAS 18001 is integrated with ISO 14001 or other standards, can we still use this
online upgrading service?
Yes, We can upgrade the OHSAS 18001 part on your integrated Management system
Documents. Pay only for OHSAS 18001 upgrading and send the payment receipt number and
the Integrated Management system Documents.

Singapore ISO Consultants

ISO 9001

ISO 9000 Standards

ISO 9000 Standards

What is the ISO 9000 Series?

What are the older (obsolete) ISO 9000 Standards?

What Standards support the ISO 9000 family?

What is ISO?

International Organization for Standardization

From Wikipedia, the free encyclopedia

History

International Standards and other publications

Standardization process

ISO document copyright

Members

Products named after ISO

ISO/IEC Joint Technical Committee 1

IWA document

Criticism

See also

References

External links

Work Place Safety and Health Risk Consultants

Other ISO Standards

Others Standards

OHSAS 18001 Upgrading

OHSAS 18001

ISO 14001 Consultants

ISO 9001-Quality Management

List of ISO Standards

ISO 1–ISO 999

[edit] ISO 1000–ISO 9999

[edit] ISO 10000–ISO 19999

[edit] ISO 20000–ISO 29999

ISO 30000–ISO 39999

ISO 80000

See also

References

Other Standards

OHSAS 18001